SOme pumps have an open bracket where you can see the shaft, but not Hayward. "@context": "https://schema.org/",
If needed, get yourself ECX1014A, bump shaft kit, for a little rebuild. Any suggestions? Hi Yolanda, also a great question first plug something else like a hair dryer or lamp into the outlet, to be sure its supplying 115V properly (or use a test meter). I assumed electrical issue but when I checked the voltage at the back of the motor and it was good I am at a loss. Jake, sounds like you got the filter up to speed. Pump is 4yrs old. I would also suspect the outlet or breaker, but you have tried a different one with the same result. The higher the pump is elevated above the water level, the more struggles this can cause. Your email address will not be published. But now Im trying to plug it in and it doesnt make any noise at all. Now if your pressure is jumping up to 20 psi very rapidly (hours or days), the filter media (sand, de or cartridge) may need to be replaced. Hi, the yellow wire could have been hit by the whirling centrifugal switch in the center rear of the motor, or could have burned thru from touching something very hot. How To Fix The Problem The motor on my Hayward super pump 2 went out so I ordered a Hayward replacement. If you have an electric shop nearby, they could test it, but if its around 10 yrs old, you may assume its dead. Attached please find a copy of the Aqua Plus Operation Manual Please note Section - Configuration Menu Items, Cell Type Selection, page 16. of and in " a to was is ) ( for as on by he with 's that at from his it an were are which this also be has or : had first one their its new after but who not they have We would like to show you a description here but the site wont allow us. We have a sand filter and no pressure gage. Hi Matt, sound like the bearings have gone bad, and now they are so bad that the shaft has locked up or is binding, and that trips the breaker. Look closely at the centrifugal switch on the rear of the shaft, to be sure its tight and is not missing parts (like the springs), engage the switch by hand (power off), to be sure that the stationary switch (located at 6 oclock) is disengaging, or the two copper tabs separate. Pressure reads 20. Inspect the capacitor, or have it tested, or just replace with same MFD rating shown. Suggestions ? Could be one of these. Replace the plumbing with a new fitting, using a silicone thread sealant and 3-4 wraps of teflon tape clockwise. Hi, Hi Pat, yes they should be plug and play, was the cord attached already, or did you install? Spillover is just the spa filling up, and overflowing into the pool, a waterfall feature is something different, with dedicated plumbing and a booster pump usually. I would test the voltage at the motor terminal board, very quickly, before the breaker trips, to be sure its between 210V-250V coming in. I remplace it and now the sistem works!! Do we need a new pump or can the electrical cord be replaced? I have called a repair company since the pump is under warranty and they told me that it is almost NEVER the pump and therefore if it is something else I will have to pay $89/hour for their serviceso I was hoping to exhaust all other possibilities before coughing up the moneyCan you recommend any tests that I can do? In particular, if the salt content of your pool water is too high, your metal screws, handrails, ladders, and covers will rust excessively. We recently had a makeover of our backyard where we replaced the concrete with pavers and it could very well be the sands and dust (yes, I had to vacuum the pool a couple times to get it clean) that got into the parts that helped speed up the demise of the pump. It was working fine (all 3 speeds) until yesterday. Why does this keep happening? Step 1: With your pump running, double-check the positions of your valves. Im thinking the new pump might be set for 230 and wiring is for 115. 4. Replaced breaker still nothing. Any ideas as to how to fix this? High water flow (>125 gpm) into the heater. Find answers to your questions about all Within the underground world of Japan, and the world at large, a certain man is known as the Evil Emperor. Hi again, I dont have a shaft seal replacement video, but there are many on youtube. When I tighten the impeller onto to the motor how tight should it be? Id call the install tech for troubleshooting. Hi Davy, So, grab the opening portion with pliers, while the wrench is holding the shaft still, and turn counter clockwise, it should come off, if it breaks, a new impeller is needed, but thats rare, they usually will budge. Or using a Clarifier after vacuuming can also be a solution. If it does not, keep reading. I will try to open it up tonight and report back. Loose wire connections or touching terminal connections cause sparking. Gail, good luck! Occasionally, while running, it trips the breaker. Unusual, but it could be the only problem, I would replace the capacitor with the same size (match the MFD number), and check that the shaft rotates freely when mounted to the pump. Still nothing. Hi Mark, in looking at the owners manual https://www.intheswim.com/images/PDFs/E1964-Manual.pdf perhaps there is a minimum speed setting that is set to high, or the programming Day/Time/Speed is set up to permit high speed only? Step 4: Verify your pumps pressure. if it does not come back on, check switches, turn breaker all the way off and back on again. Like it is getting through the shaft seal but the seal is brand new.. any thoughts? They are easily replaceable. Thanks for your time! This week the motor The salt cylinder is clean. Reinstall and add new DE powder. The Aquatrol kind of jumped and the breaker tripped. If it is on low it works properly. Baal School; Skill Training for Girls Hi Michelle, If the pump and motor are too large and powerful for your filter size, it would create this situation. My guess is they would pronounce it DOA, but may find something interesting, or may find no problem at all, which would lead you to suspect the wiring, breaker, timer the source of power. Any advise on what is the problem? Be sure that all pool valves are open and any wall plugs are removed before turning on pump. After troubleshooting using your TS guide, I found on page 36 where it says to check the top rectifier I have 24VAC from the board (where the orange wire plugs into) to the ground. Also, DE filters need to be opened up and hosed down completely clean every 6-9 months, and then started up again with a full charge of DE powder. If the No Flow LED is flashing, wait 60 seconds after starting your pump and filter. Slide your main switch to the AUTO position. A hum sound is usually associated with a bad capacitor (motor rear, 9 oclock), however the capacitor is a battery that is only used on start-up, and is released within a second of start-up, but still could be related. If you suspect your breaker has broken, call a certified electrician to further diagnose the problem. When we turn on power, the pump does not make noise but the timer box and the circuit box make a light humming noise and then the circuit tripped. If flushing and draining does not help, it is time to open up the filter tank, remove the grid assy (or flex tube nest), and after cleaning very well with a hose, soak it in a DE filter cleaner solution (5-gal bucket works well for Perflex). If there is air in the basket it hums away loudly and sucks great to prime and fill the basket (the saltwater thing even appears to be working). Are you using DE powder or enough DE powder? When running through all these checks and balances if it is noticed that there is not bond wire or that the tightening screws are not all secure, correct the issue. Hi I have a variable speed ecostar and am now having the drive error, drive stalled. Juat replaced motor. The LED light should go out. Increased flow this year may be from the new sand, and higher flow makes it easier for air leaks to appear. I will be purchasing a replacement pump and have it installed, but I wonder if Id need to just have the breakers tightened in the panel box? Finally, could be that the voltage is not quite right, one of the legs (power wires) not providing enough power. After communication is established, if it is lost for 30 s, the error will be displayed.
The burnt odor is not a good sign a new motor may be needed soon! Before you test your capacitor, take note of its appearance. },
The pump is a Hayward Superpump SP1600X with a UST1102 motor. Ive had the pool for about a month and all has been fine but while I am ordering a new hose is there a replacement hose I can use in the meantime? Your chlorine generator is still producing chlorine at the moment, which is a good thing. The shaft turned with zero resistance. What is happening? Any ideas? Nothin seems to be leaking anywhere. Thanks for your insight. No special tools or lube needed. Do I need to clean filter? LibriVox is a hope, an experiment, and a question: can the net harness a bunch of volunteers to help bring books in the In a Quirked world where most people have a superpower-like uniqueness to them, His is among the most dangerous. Check the mechanics of the switching mechanism. Motors have a thermal overload switch (in the rear of the motor, top-dead-center, at 12:00). It is not just the connection that is leaking, the pump body itself has sprung at least one leak near the neck of the top fitting. I think it only screws on in one direction, but unscrew it to check When in Filter Position, water should route in only one direction. Pat. If you have a multiport valve, set it on Recirculate, to bypass the filter, and rule out any problems there. If stuck from rust build-up, move the capacitor (located at 9 oclock) and/or the thermal regulator (located at 12 oclock), out of the way, so that you can fit a 7/16 open end wrench on the slotted part of the shaft, behind the centrifugal switch that is screwed onto the end of the shaft. Im assuming that the motor makes no noise at all? My Hayward h250 propane heater keeps blowing fc1 and fc2 fuses immediately after plugging in. I shut the pump down the other night and it will not run. Products, View There is an o-ring on the union, and also on the valve stem, and they can start leaking over time. Pump making loud grinding noise, any solutions. View Details Usfitnessfinder.com. (I just bought the house and am new to pool upkeep.). Air leaks are another source of priming issues. In the last couple weeks it started getting louder at various times throughout the day. You may have a partially clogged burner orifice, which is the brass spray tip on the end of the burner tube, where the gas shoots out of the manifold. "caption": "In The Swim Blog"
Impeller turns from inside basket. which can clog the tiny gears, or wire issues, burned spots or chewed wires (ants). This is a salt pool not sure if that matters in the question. I think I have some air leakage on my supply side of my Hayward Super Pump. Then I saw a HS code. When the valve is positioned on the filter, it should slide over the standpipe tube, or the center pipe that is connected to the laterals will slide up into the bottom of the valve, and the valve is pushed down to make a tight fit against the filter flange, and then the clamp is supposed to hold it tightly. If you are getting correct voltage into the rear of the motor (120V or 240V, +/- 10%), but still the motor makes no noise at all, its likely DOA the motor at least. Everything coming in appears to be tight. Plaster and vinyl surfaces in particular, can become damaged when exposed to hot summer weather, and stained, if that applies or matters in your case. I have a thermal switch on it,thank goodness or the motor would probably be fried. Flush out the housing to clear debris, then refill with water. Thanks. If there's one thing for certain about pool equipment, is that they will all break down at some point in time. We would like to show you a description here but the site wont allow us. My pool guy went directly to saying I need a new one. Not normal, but cant see a reason why that would cause the seal to fail. 3 possible solutions. Step 1: Check your system to confirm that you have programmed the correct cell size. Or it could be a bad breaker, but usually not. HELP! If there isnt any apparent damage, keep reading. This he says is because the drive is intermittently failing and the pump will need to be replaced. I see a break on the back side of control board where the wires plug into a 6 prong male connector. Articles and resources for swimming pool owners and DIYers. Question my Aquaririte is 3 years old. Hi, make sure that the switches are not loose, the centrifugal switch on the end of the shaft and the Stationary switch at 6 oclock. Hi, I have a hayword C48L2N134B3 1.5 HP pool pump. Another reason for a smoking pump is an incorrectly installed shaft seal, or blown capacitor. Hi, if the switch wont flip to on, the timer tripper could be right at the point where it is about to trip, making it hard to turn to on. They are cheap and easy to replace. If so, you may try to glue them in place with JB Weld or similar, and if that doesnt work, a new housing would be in order. Hi thanks for speedy reply the breaker is 20 amp with a GFCI. Ive waited a few hours and tried again but no luck. Leaks can also come from loose drain plugs, or loose bolts on the seal plate, connecting the motor to the pump. I replaced the entire pump motor and the same thing happened. could be the motor, if the shaft has worn unevenly, or if there are grooves or rust on the shaft. If your cell looks like 4B, follow the instructions below for cleaning your cell. Any ideas on what may be going on? A pool guy who has since stopped operating put it in. I replaced the start capacitor as that sounded like that was the most likely culprit based on everything I read, but noise still persisted. Lighting, Learn About First eliminate water flow issues, then gas flow issues, and finally the low voltage electric currents that run between pool heater components. I have a new fiberglass pool and ever since I operate it the pump trips the breaker in most cases overnight hours between 2 timing sessions (pump not running). Check the motor vent holes, (bottom front) to be sure they are not clogged. Hi probably not related to the vacuuming, but sounds like a motor problem. Hard for me to say if the motor is shot, but it has sure had a rough life! I have to say Ive never touched it before during almost 6-years of normal operation. You could use a small plug-in pump timer that would allow you to not unplug, just flip the switch to off. I think the problem is a nick in the face of the salt cell that the unions o-ring seals against, but I cant feel anything there so its not like a giant burr or anything. View Details Usfitnessfinder.com. We have just replaced the seal assembly as suggested by a Hayward rep already. Is this enough to cause it not to prime or is there an issue with the impeller? If it sounds loud and grumbly, that can be a sign of cavitation, being starved for water, from not enough water being supplied (it wants more). Your options are to 1). Anyone have this issue or have any recommendations? 3. pipe going into pump Inspect the circuit board, blow off with some air, and look closely at the 3 wires for any insects, spiderwebs or corrosion of any type. Hi, I have a filter timer and a cleaner timer that are side-by-side. Motor running very hot, almost like in a bind. I did notice the on/off switch was mushy moving from the on and off positions. Something got fried, sorry! What do I need to do to fix this? BTW, this can be caused from a water hammer effect, running the pump and then shutting off flow suddenly, or the fitting could have been overtightened to begin with, 7 years ago, and age caused it to give way. If it continues, a new o-ring might be the ticket, yes. Wouldnt turn back on for a while even after manually flipping the switch. Put your foot on the motor and apply a little weight, to see if the noise stops. Minglin. What more can I do or will the bubbles resolve on its own? Thanks in advance for any help. Is this the problem and should I get i checked or just replace it? If I try to shut it off, nothing happens. Might be 2-years here is a chart on reading Hayward serial numbers, to find date of manufacture https://www.totallyhayward.com/techservices/attachments/Serial%20Number%20Read%20REVISED%201-2012.pdf, I have to reprime my hayward pump everytime I turn it on. If you find out, I would check the owners manual for information related to your symptoms. Put a meter on the terminal board, and see if the voltage coming into the motor is fluctuating or dropping off, when the motor cycles. Override this by moving the Main Switch to Super Chlorinate. They disappear when the pump is at a high speed. Please note: The majority of our literature and brochures are in English only. it runs about 30 minutes and trips the breaker. Second thought is are the pipes plumbed into the valve correct? The sound you reference pumping rocks sounds like a pump that is cavitating, or starved for water. Please note: The majority of our literature and brochures are in English only. Have had it for 4-5 years and have had no issues. Please help! If it does make a humming or buzzing sound briefly and trips the breaker, check that the shaft rotates the impeller freely, and if so, replacing the capacitor is usually the fix. Hi Kevin, I think I would check the capacitor(s), maybe replace them if they test weak, or look cracked or damaged. Ive never owned a pool before and didnt have any problems all summer until the last 2 weeks. There is also a faint burnt odor. Hi there, I have a 2-speed (hi and low) Hayward pump. Could be the use of a clarifier or flocculent that is clogging the sand? v when it is turned to 230v and re wired for 220-230 v it makes no noise at all. I have an sp3400vsp pump. Thanks. Hi Ric, is the SF service factor rating the same on both motors (new and old)? Is there a break in period for the unit or do I need to call the technician? Hi Tom, there is an o-ring that seals up the tank flange to the valve flange, its usually on the valve, when you remove the valve, might need replacement and/or a good cleaning and lubing. Most Common areas include the pump lid (must be very tight, with lubed lid o-ring), and the threaded pipe that comes into the FRONT of the pump (must be very tight and sealed if loose, use Pool Putty to fix, or replace the fitting) the effluent or exit pipe fitting leaking will not draw air, that is on the pressure side not the suction side. stranger things backpack hot topic. Air could also be entering the pump from the threaded pipe or union that is attached to the inlet port, which may also spray or drip when the pump shuts off. Step 3: Ensure that there isnt anything obstructing or blocking the flow. Hi John, that is going to be either a cavitation noise, where the pump is starved for water, or if this noise is new, it would likely be the front and/or rear motor shaft bearings wearing out. Now what? You can also turn off the pump at the breaker which provides power to the timer. We have a Hayward Swimpro Lx 1.0 hp and have a slow leak coming from underneath, maybe in between the housing and the motor. this is the black cylinder in the rear, at 9 oclock. 2. Hi, my Hayward pump is about 5 years old. A large pair of channel type pliers can be placed on the impeller, over a cloth, and given some persuasion. Specialties: Cycling, Kickboxing, The Twelfth Edition of Business Research Methods reflects a thoughtful revision of a market standard. I dont see that code listed. any ideas? partially collapsed, or partially clogged skimmer line. Hayward AquaTrol HP Main PCB | GLX-PCB-TROL-HP - Pool Supply Unlimited https://www.instagram.com/inyopools/JOIN our circle on GOOGLE+ https://plus.google.com/+Inyopools/postsAs with any automatic salt chlorine generator, tune ups are needed from time to time. You may be able to remove the basket and reach thru the volute to the eye of the impeller, and may be able to feel debris. I would guess this is what is happening, and if so your service company is either uneducated or dishonest. Shock the pool first and overfilter, before pulling pump. Pump motors are continuous duty, meaning that they are meant for continuous operation, it wont harm the motor, or cause it to overheat. Got a new motor, it made humming noise since day on,if i help it spin it works so I changed the capacitor and still the same, humming and if I help it to spin it goes fine, any suggestions? Thank you. If your pool is fairly small, without spa and water features, you can also consider using a Pentair SuperFlo VS pump, which has fewer features than the Intelliflo, but also costs much less. It could have also overheated, when this happens, it will work again after cooling down. dhp faux leather club chair; hanna salinity tester calibration; Additional causes for low water flow in your pump are debris build-up or dirty equipment. If the filter multiport was recently re plumbed, be sure that the pipe from the pump goes into the valve port labeled PUMP, and the pipe to the pool is connected to the valve port labeled RETURN. Hi Rick, if thats a new thing, there is probably something loose and leaking (air) when the pump shuts off. Hi there, I made the very unfortunate decision to rent my home to a friend. If the shaft is free turning, but the pump does not turn on, check power connections. Hayward Pool Heater Troubleshooting - In The Swim Pool Blog If your cell looks like 4A, continue to Step 4. That is the black cylinder in the rear of the motor, located at 9 oclock. I have a Hayward super pump 1.5 hp. Happens all the time to pool pumps, and the way to un-stick it is to do some disassembly in the rear of the motor, to get a wrench on the slotted rear of the motor shaft, and work the shaft back and forth for a minute, to break the rust seal, and get the shaft to turn again. I have a Hayward Super II pump that has had a small leak between the pump housing and seal plate. If needed, you could replace just the motor, and the shaft seal, and save a few hundred bucks. Test the capacitor for voltage, or just replace with exact MFD no. You could remove the filter grid completely from the tank (and clean well), start the pump without the grid assembly inside (removing most of the resistance) and see how the water flows. That could explain the pumping problems. This happens even when the filter and skimmer basket is clean. Shaft seal went out twice and I have a groove in the motor shaft now. If clogged, open the pump up, and ream out the impeller vanes with a flexible wire. Hi, yes shaft seal failure. The motor can be tested briefly without being bolted onto the pump. Hi Stephen, your spa waterfall, is that a spillover or an actual waterfall feature? Or to a light switch and then to a breaker, that would be more of a standard installation. Dont let pool pump problems drive you crazy! When you first turn it on it works great with strong suction. Probably not your pump basket being full causing this but improper air flow caused by debris/dust. If you had a multiport valve, you could put it on recirculate and verify, but since perflex have no such valve, the only other test would be to actually plumb around the filter, by installing a bypass valve and line, or just temporarily routing plumbing around the filter, to bypass the filter completely. When I finally turned it off again it would not come back on. Excessive voltage or amps can cause the problem. I have a Hayward pro max 1.5hp with sand filter but the suction into basket is not good. Hi. Hi Shannon, assuming that your pump is single speed (not dual speed or variable speed), it runs at a constant 3450 RPM, and is not possible to run at a lower speed. I have a new Power-Flo Matrix pump. When it starts up it occassionally will blow the breaker. If your pump has an open bracket (where you can see the motor shaft), you can grab the shaft with your fingers or straight pliers, to break any rust. The pump will draw air in if it can it is easier than pumping water, or the path of least resistance. To view these documents, you will need to download the free Acrobat Reader, which Attached please find a copy of the Aqua Plus Operation Manual Please note Section - Configuration Menu Items, Cell Type Selection, page 16. Tool pump out of storage and hooked up as normal. So, it either needs a new motor, or new internal parts, or possibly a whole new pump. You can also pressurize the suction lines using a Drain King, connected to a garden hose and inserted at the skimmer, with a plug inside of the pump on the incoming pipe, or setting the multiport valve on closed. Maybe a complete reboot at the circuit breaker could be the answer, or a reset on the pump control panel. After doing some reading, I now understand that the IG pump shouldnt be used with the AG pool and weve been doing the wrong thing for almost 30 years. hayward blue essence troubleshooting. Its a little over 3 years old and the cell checked out fine. Its never happened before. Step 2: Select your product type. The problem lies where the power dies, so it could be a bad timer motor, timer relay, timer switch, or a bad pump motor. Step 2: Did you properly install your switch? of and in " a to was is ) ( for as on by he with 's that at from his it an were are which this also be has or : had first one their its new after but who not they have 25 The following steps will provide a guide on how to recalibrate a Hayward Aqua Rite. Occasionally the salt level on the Hayward Aqua Rite may not match the actual salt level of the pool. My prior one was over 12 years old so Im feeling uncertain. If lots of air churns when you shut the pump off, and the water quickly blasts out of the pump, thats likely a suction side air leak. hayward super pump C48L2N134B1. Holes in grids, or stitching coming apart I have it on a 15 amp breaker with a few other items, the motor after running is very hot to the touch. When the pump comes on a massive amount of bubbles comes out of the return line in the bottom of the pool. Step 2: Verify the accuracy of the salt readings (2700-3400 pm) with an independent test kit or by taking a water sample to your local pool store for testing. Thanks, Hi Nancy, this is a common problem water leaking out of the backwash line, while filtering. Scoop out debris left in basket area, and try again. Or could it be a dirty motor or ground wire that isnt connected well enough? Hi Rose, Its common that winterized pumps may freeze up, caused by a rust layer inside the motor. You might be surprised by how many people neglect to check this area. 4. leaky valve or unions in front of pump I am getting air bubbles coming from my return jets in my pool. hayward blue essence troubleshootingpeel and stick tile 914665 hayward blue essence troubleshooting. If so, put the meter on the terminals where to cord connects inside the motor and see if there is power there. Ob, and its just over 4 yrs old. Hello, my motor runs for 20 seconds then stops. Have a Hayward pump for above ground pool.when I start the pump it works properly and then itll stop pumping water. Now if its not an air leak, surging can also be caused by a clog in the pipe, usually a solid object like a golf ball, getting sucked back and forth in the pipe. I replaced the impeller ring and noticed it Yesterday I plugged it in to filter and where the plug goes into the 3 foot heavy duty extension it sparked smoked and created a small flame. When turned on, it clicks in and off every few seconds. We have all these parts here: https://www.intheswim.com/c/valve-parts, I Installed a new Hayward VCSB216V solar pump. American Freight San Antonio, First, in regard to my Hayward pump basket lid, it is hard to turn counter clockwise, when i need to remove it but it does turn. Hi Kenny, not to my knowledge, you should see some display even without gas hookup. The third thing to check would be an obstruction on the pressure side of the pump, clogged impeller, clogged filter, closed return side valves or plugs in the wall. I purchased a hayward powerflo matrix 1.5 pump and Proseries 21 Filter a week and a half ago. Hi Mary, flocculents usually produce a fluffy precipitate that is vacuumed to waste, because it clogs ups the filter. On a Hayward pump with clogged impeller, you can remove the basket, reach through the small hole with your fingers (pump off! Next, maintain the proper salt levelin the pool. If so, it will always read 100%. We just opened our pool up cleaned everything out put new D.E. cd77petanque.com Informacin detallada del sitio web y la empresa
Psalm 91 Commentary John Macarthur,
Giedi Prime Population,
Shooting In Portsmouth, Va Today,
Data Architecture Accenture,
Brunswick County Clerk Of Courts,
Articles H